D1 Three In One Multifunctional Hair Comb Self Developed Brushless Motor Platform
D1 multifunctional hair comb with a self-developed 110,000 RPM brushless motor, 3-in-1 drying, straightening and curling, MCH heating and 220g body.
Self Developed Brushless Motor
,Three In One Styling
,Drying Straightening Curling
D1 Multifunctional Hair Comb with a Self-Developed 110,000 RPM Brushless Motor
Self-developed also means predictable service life. The motor runs at a controlled duty cycle, the MCH heating module is thermally isolated from the electronics, and the firmware enforces auto pause and standby behaviour so the unit does not sit at temperature between passes. For buyers, this multifunctional hair comb is a single SKU that covers drying, straightening and curling in one listing, which cuts catalogue complexity and lets a retailer compete in three search categories with one product.
Key Specifications
| Model | D1 |
|---|---|
| Functions | Hair drying, straightening and curling in one unit |
| Motor | Self-developed brushless DC motor |
| Motor Speed | 110,000 RPM |
| Heating Module | MCH heating module |
| Airflow Settings | 3 levels |
| Temperature Settings | 4 levels |
| Display | LCD colour screen |
| Rated Power | 1400W - 1600W |
| Rated Voltage | 220-240VAC, 50/60Hz |
| Net Weight | 220g |
| Dimensions | 320 x 34 x 46 mm |
Why the Self-Developed Motor Matters in a Comb Format
- A comb body leaves very little room for airflow hardware, so the 110,000 RPM brushless motor had to be redesigned in axial format to fit the 34 mm barrel.
- The self-developed driver keeps speed flat as the comb passes through wet or thick sections, which prevents the airflow collapse typical of adapted fan motors.
- Three functions share one motor: drying uses full airflow, straightening uses airflow plus MCH heat, and curling uses the reduced-flow setting.
- At 220g the multifunctional hair comb can be used one-handed for a full styling pass without wrist fatigue.
- MCH heating reaches working temperature quickly and holds it, so the straightening plates recover between sections instead of cooling down.
- Auto pause and standby modes cut element power when the comb is set down, which reduces energy use and improves safety in a home setting.
Application Scenarios
- Home users replacing a dryer, a flat iron and a curling brush with one device.
- Salons wanting a finishing tool that dries and styles in a single pass.
- Travel retail and hotel channels where a compact 220g styler is preferred.
- Marketplace sellers needing one SKU across three styling search categories.
Manufacturing & Quality Control
Each self-developed 110,000 RPM brushless motor is dynamically balanced, hipot tested at 1,500V and run 30 minutes at full load before assembly. The MCH heating module is cycled 10,000 times and monitored for temperature drift, while the LCD, airflow switch and temperature switch are endurance tested as a group. Finished D1 units are checked for weight within plus or minus 5g, output temperature at all four settings, and auto pause response time before cartoning.
Frequently Asked Questions
Q: How does one comb dry, straighten and curl?
A: The self-developed 110,000 RPM brushless motor supplies the airflow for drying, the MCH module adds controlled heat for straightening, and the reduced-flow setting with the curved edge shapes curls, all from the same 220g handpiece.
Q: Is the motor really developed in-house?
A: Yes. Impeller geometry, duct design and driver firmware are ours, so airflow, noise and duty cycle are tuned as one system rather than limited by an off-the-shelf motor.
Q: What voltage does the D1 use?
A: 220-240VAC at 50/60Hz, with 1400W to 1600W rated power. This configuration suits EU, UK, AU and most Asian markets.
Q: What is the minimum order quantity?
A: 2,000 pcs, with mixed colourways allowed, and samples available from stock for evaluation before the production run.